progress

  • Zero distance close service

    Germany and Italy "hui" pasta to welfare activities, gourmet class, lifestyle, humanistic care, and other forms, communicate with you "zero distance", interactive "zero distance", and "zero distance" service.Germany and Italy is around you, the service is on your side!

    Q:Motor and light does not operate

    A:1、Check the plug and insert completely.
    2、Change the bulbs.
    3、Contact the distributor for service.
    4、Contact the distributor for service.

    Q:Motor cannot operate but the lights are working

    A:1、Contact the distributor for service.
    2、Contact or replace the capacitor.
    3、Contact the distributor for service.

    Q:The appliance vibrates or shakes while in operation

    A:1、Install the appliance with a solid and steady wall.
    2、Fasten the motor tightly with the body.
    3、Contact the distributor for service.

    Q:Only one or two buttons can function while others are not working

    A:1、Contact the distributor for service.
    2、Re‐connect any loose wires into the control board.

    Q:Weak Suction

    A:1、Lower the appliance's installation.
    2、Remove the blockage inside the duct.
    3、Do not open too many windows during cooking to improve the environment for suction.
    4、Clean or replace the filters.

    Q:Oil Leakage

    A:Install the appliance in balance level.

    Q:Range Hood FAQ

     FAULT 

    CausesRemedies

    Motor and light 

    does not 

    operate

    Power plug is not insert completely

    Check the plug and insert completely

    The light bulbs are blown

    Change the bulbs

    The wire and/or the cable disconnected

    Contact the distributor for service

    The light's transformer is damaged

    Contact the distributor for service

    Motor cannot 

    operate but the 

    lights are working

    The impeller are stopped

    Contact the distributor for service

    The capacitor is disconnected and/or damagedConnect or replace the capacitor

    The motor is damaged

    Contact the distributor for service

    The appliance 

    vibrates or 

    shakes while in 

    operation

    Installation of the appliance is not 

    steady or the hanging wall is not solid

    Install the appliance with a solid and steady wall

    The motor is not fixed tightly

    Fasten the motor tightly with the body

    The damaged impeller break the balance

    Contact the distributor for service

    Only one or two 

    buttons can 

    function while 

    others are not 

    working

    The control panel is not in order

    Contact the distributor for service

    Connection with the control board is looseRe-connect any loose wires into the 

    control board

    Weak Suction

    The appliance is installed too high 

    from the cooking hob

    Lower the appliance's installation
    There are blockage in the exhaust 

    duct

    Remove the blockage inside the duct
    Air convection is too strong around the applianceDo not open too many windows during cooking to improve the environment for suction
    The mesh filters or charcoal are dirty or cloggedClean or replace the filters
    OiI LeakageThe appliance is not installed in balance level

    Install the appliance in balance level

    Q:Three minutes after turn on power, the heat circle is still not red

    A:1、Connect power plug.
    2、Call after‐sales service.

    Q:Three minutes after turn on power, the heat circle is still not red

    A:1、Connect power plug.
    2、Call after‐sales service.

    Q:Heat circle works intermittently

    A:Normal phenomenon

    Q:Heat indicator light is off, while ceramic glass surface is very hot

    A:Call after‐sales service.

    Q:Heat time lengthens

    A:Change cookware.

    Q:Ignitor doesn

    A:1、Connect power.
    2、Replace High‐voltage wire.
    3、Replace High‐voltage wire.
    4、Replace pulse ignitor.
    5、Replace or adjust Micro switch.
    6、Install the battery properly.
    7、Adjust to 5‐6mm distance.
    8、Turn on gas supply.

    Q:Flame Failure Device open valve time lengthens

    A:1、Adjust throttle position.
    2、Adjust thermocouple.
    3、Replace Flame Failure Device.

    Q:Backfire

    A:1、Adjust burner cap.
    2、Replace Burner or adjust Throttle.
    3、Adjust burner cap.
    4、Adjust throttle.
    5、Adjust burner cap.
    6、Adjust throttle.

    Q:Hob FAQ

    A:

    Problems
    CausesSolvent

    Three minutes after 

    turn on power, the 

    heat circle is still 

    not red

    1Power plug is offConnect power plug
    2Internal connection is brokenCall after-sales service

    Heat circle works 

    intermittently

    1

    It is on auto temperature control or the temperature is on highest protectio

    Normal phenomenon
    Heat indicator light 

    is off, while ceramic 

    glass surface is very 

    hot

    1Heat indicator light is brokenCall after-sales service
    2Internal connection is broken

    Heat time lengthens

    1Cookware bottom concavity is too big

    Change cookware

    2

    Cookware bottom area is too big

     Ignitor doesn't 

    work.

    1Power is off connection

    Connect power

    2High-voltage wire leakage

    Replace High-voltage wire

    3Ignition porcelain head leakageReplace High-voltage wire
    4Pulse ignitor is broken

    Replace pulse ignitor

    5Micro switch coonection is not good

    Replace or adjust Micro switch

    6Battery installation is not goodInstall the battery properly
    7 Distance between Ignition porcelain head and Burner cap is improper

    Adjust to 5-6mm distance

    8Gas supply is off 

    Turn on gas supply

    Flame Failure 

    Device_ open 

    valve time 

    lengthens

    1*Throttle position is improperAdjust throttle position
    2Thermocouple position is improper

    Adjust thermocouple

    3Flame Failure Device doesnt workReplace Flame Failure Device
    Backfire1Burner cap position is improperAdjust burner cap
    2*Burner leakage or Throttle opens too wideReplace Burner or adjust Throttle
    3Burner cap is up side downAdjust burner cap
    Flameout1*Throttle opens too wideAdjust throttle

    Big noise

    1Burner cap position is improperAdjust burner cap
    2*Throttle opens too wide

    Adjust throttle

    Q:About the Electrical safety

    A:1、This appliance must be only connected by a steered electrician.
    2、In the event of a fault or damage to the appliance: Take the fuses out or switch off.
    3、Repairs to the appliance must only be carried out by qualified service engineers. Considerable danger may result from improper repairs. If repairs become necessary, please contact our Customer Services or your dealer.

    Q:About the Child Safety

    A:Never leave children unsupervised when the appliance is in use.

    Q:For Safety whilst Using

    A:1、People (including children) who, because of their physical, sensory or mental capabilities or their inexperience or ignorance are not able to use the device safely should not use this dev-ice without supervision or instruction by a responsible person.
    2、This appliance is intended to be used for cooking roasting and baking food in the home.
    3、Take care when connecting electric appliances to sockets nearby. Do not allow connecting ads to come into contact with or to catch beneath the hot oven door.
    4、Warning: Risk of burns! The interior of the oven becomes hot during use.

    Q:How to avoid damage to the appliance

    A:1、Do not line the oven with aluminum foil and do not place baking trays, pots, etc. on the oven floor, as the heat that builds up will damage the oven enamel.
    2、Fruit juices dripping from the baking tray will leave stains, which you will not be able to remove.
    3、For very moist cakes, use a deep tray.
    4、Do not put any strain on the oven door when open.
    5、Never pour water directly into the oven when it is hot. This could cause damage to or discoloration of the enamel.
    6、Rough handling, especially around the edges of the front panel, can cause the glass to break.
    7、Do not store any flammable materials inside the oven. These could ignite when the oven is switched on.
    8、Do not store any moist foods inside the oven. This could damage the oven enamel.
    9、After switching off the codling fan, do not keep uncovered dishes in the oven. Moisture may condense in the oven interior or on the glass doors and may get into the units.

    Q:What if the heating period is too long?

    A:1、Check the surface of the evaporation pan. If there is a thick layer of scale, clean the pan with scale.
    2、The door seal may be damaged and the steamer door may leak.

    Q:What is the reason for not producing heat if the steamer is started?

    A:

    1、Please check if the steamer door is closed.

    2、Whether the tank has water and is in place.

    3、The steamer door switch may be damaged.

    Q:What is the reason if the steamer fails to start?

    A:1、The circuit board fuse blows, causing the board to be de-energized.
    2、Turn on the power again and turn on the steamer.

    Q:What are the differences for steam oven with preheated or non preheated food?

    A:Choose according to your own tastes and preferences to decide whether to put in the dishes after preheating. Dishes cooked usually have good taste after being preheated by steam oven. The color is bright and the moisture is just right, while non preheating dishes are relatively ripe, with more moisture and deeper color.

    Q:How to correct use the microwave oven

    A:

    1、The appliance is intended for domestic use only: to cook, defrost, and reheat and to grill food. Any other usage is not supported by the manufacturer and could be dangerous. The manufacturer cannot be held liable for damage caused by improper or incorrect use of the appliance.

    2、Never use the microwave to store or dry items which could ignite easily Moisture evaporates. Fire hazard. This appliance is not a toy! To avoid the risk of injury, do not allow children to play on or near it or to play with the controls.

    Supervise its use by older children, the elderly or infirm. If allowing older children to use the appliance without supervision please ensure that they are aware of how a microwave oven works and understand the dangers of improper use.

    Q:Disposal of your old appliance

    A:Before disposing of your old appliance, first make it unusable. Disconnect it from the mains, cut off the cable near the appliance and cut off and render any plug unusable. This should be done by a com-patent person.

    Q:The manufacturer will not be responsible for the damage caused by the following operation

    A:1、The manufacturer cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions. Operating the appliance with this type of damage will result in microwave leakage and present a hazard to the user.
    2、Never open the casing of the appliance Tampering with electrical connections or components and mechanical parts is highly dangerous and can cause operational faults or electric shock.
    3、Before connecting the appliance to the mains supply, make sure that the rating on the data plate corresponds to the voltage and frequency of the household supply. This data must correspond in order to avoid risk of damage to the appliance. Consult a qualified electrician if in any doubt.
    4、Do not connect the appliance to the mains electricity supply by an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating)

    Q:Always ensure that this type of procedure is supervised

    A:1、Do not uses the microwave function to heat up cushions or pads filled with cherry kernels wheat grains, lavender or gel, such as those used in aromatherapy. These pads can ignite when heated, even after they have been removed from the microwave.
    2、Exercise caution when cooking or reheating food with a high sugar content, e.g. Christmas adding. If heated for too long, the sugar may caramelize or ignite.
    3、Do not use full power to warm empty dishes.
    4、Do not use the appliance without food, or if it is incorrectly loaded.
    -Never cook or reheat food or liquids in sealed containers, jars or bottles. With baby bottles, the screw top and teat must be removed.

    Q:When using browning dishes, you need to pay attentions as followings

    A:1、Always use oven gloves when handling the browning dish to avoid burns.
    2、Never place the browning dish directly onto a table or work surface. Use a suitable heat. Resistant mat, grid or board to protect the work surface or table and prevent heat marks.
    3、Browning dishes should only be used in a microwave oven, or as a serving dish. In a conventional oven the special glaze would suffer damage.

    NO FAQS
    Q:How to install the sterilizer correctly

    A:1、The appliance must be installed by a qualified professional according to the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.
    2、The appliance must be installed to an adequate circuit with complete installation.
    3、Socket needs to be within 1.2m in radius from the wire interface with rated current above 10A.
    4、An effective earthling system should be guaranteed continuous and complete; it's prohibited to attach the earth wire to any pipe, phone wire or lightning arrester which may cause serious consequence.
    5、Use separate socket for this appliance only, Install the socket into a power leakage protection circuit to enhance the safety.
    6、This is not a bearing table

    Q:How to use

    A:

    1、Open or close the drawer in a clinic direction, do not push too hard
    2、Place dishware upright after wash and drain, keep a certain distance between dishes to ensure the disinfection circulation. Keep the dishes away from the vent to get a better drying effect.
    3、Setting:Connect to the electricity supply after been fully installed: make sure the drawer keep closed when working. There would be a prompting sound with a ’Di’ once the connection is done.

    Q:What should you pay attention to when using?

    A:1、Actions non compliance with these waning and safety Instructions will be dangerous to the user.
    2、Only use genuine original spare parts and accessories with this appliance.
    3、Do not use alternating current other than 185v-245v, otherwise the appliance could be damaged. Consult a qualified electrician if in any doubt.
    4、Do not open or try to fix the appliance other than a qualified electrician.
    5、Do not spray waters or liquid to the appliance when working, otherwise may cause a dangerous electric shock or short circuit.
    6、Do not use this appliance to lacquerware, heat-sensitive plasticware, or things other than tableware.
    7、It's recommended that the tableware should be emptied before put into the appliance.
    8、It's recommended that one should open the drawer after 20 minutes after the operation finished avoiding any leak or burn.
    9、The appliance would be automatically stopped running once the drawer forced to open to prevent any burn.
    10、Do not force to open the drawer when it's under function.

    Q:How to keep the sterilizer clean?

    A:

    Please stop the entire program and unplug the appliance, wait till the machine coo down before the clear and maintain procedure.

    1、Using a soft cloth with neutral detergent to clean the drawer, dish racks and bladder if needed, make sure to wipe the detergent with wet cloth then buff dry with a clean one.
    2、Empty the water plate regularly to avoid any overflow.
    3、Gas, alcohol, or solvent is prohibited for cleaning, it‘ll cause crack and discoloration of painted film.